INSTRUCTION MANUALPART NO. D27918 Rev. 1Copyright © 2003 Delta MachineryESPAÑOL: PÁGINA 25FRANÇAIS: PAGE 49To learn more about DELTA MACHINERY visit o
10- ENGD279186. Reinstall cleaning solution tanks. Tilt cleaning solution tanks toward engine,slide onto handles, and snap into place.7. Attach cleani
11- ENGD27918OPERATING INSTRUCTIONSBASIC ELEMENTS OF A PRESSURE WASHERHigh Pressure Pump (located inside the shroud): Increases the pressure of thewat
12- ENGD27918BASIC ELEMENTS OF ENGINERefer to the engine manual for location and operation of engine controls.Choke Control: Opens and closes carburet
13- ENGD27918HOW TO USE SPRAY WAND:Your pressure washer is equipped with a multi-adjustable spray wand with bothhigh and low pressure settings. The hi
14- ENGD27918HOW TO USE THE DUAL TANK CLEANING SYSTEM NOTE: Use only soaps and cleaning solutions designed for pressure washer use.Do not use bleach.T
15- ENGD27918READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNITWhen using the high pressure setting, DO NOT allow thehigh pressure spray to come in
16- ENGD279184. Connect water source to pump inlet.NOTE: Water source must provide a minimum of 5gallons per minute at 20 p.s.i. 5. Connect high press
d. Before reconnecting cleaning solution hose to chemical injector barb fittingmake sure that any remaining cleaning solution has been completelydrain
18- ENGD279181. Shut off the pressure washer and turn off the water supply.2. Disconnect spark plug wire to insure the unit will not start while perfo
19- ENGD27918ENGINEConsult the Engine Owners Manual for the manufacturer's recommendations forstorage.PUMP1. Drain all water from high pressure
2- ENGD27918TABLE OF CONTENTSSAFETY GUIDELINE/DEFINITIONS ...2CONSUMER SAFTEY INFORMATION...2IMPORTANT SAFETY INSTRUCTIONS ...
20- ENGD27918DUAL TANK CLEANING SYSTEM1. Turn control valve knob to the down (off) position.2. Remove cleaning solution hose at chemical injector and
21- ENGD27918TROUBLE SHOOTING GUIDEPROBLEMEngine will notstart (see EngineManual forfurther engine troubleshooting)No or lowpressure (initial use)CAUS
22- ENGD27918Water leakingat pumpWater leakingat gun/wandconnectionNo or lowpressure (afterperiod ofnormal use)PROBLEMCAUSECORRECTIONWand not in low p
23- ENGD27918NOTES
24- ENGD27918D27918WARRANTYDELTA MACHINERY warrants to the original purchaser that all products covered under this warranty are freefrom defects in ma
3- ENGD27918IMPORTANT SAFETY INSTRUCTIONSRead Operation Manual. Do not operate equipment until youhave read Operation Manual for Safety, Assembly, Ope
4- ENGD27918• Fuel or oil can leak or spill and couldresult in fire or breathing hazard, seriousinjury or death can result. Fuel or oil leakswill dama
5- ENGD27918• Reactive force of spray will causegun/wand to move, and could cause theoperator to slip or fall, or misdirect thespray. Improper control
6- ENGD27918The powerful spray from your pressure washer is capable of causingdamage to surfaces such as wood, glass, automobile paint, autostripping
7- ENGD27918HandleBagged PartsNozzle CleaningKitEnglish/Spanish/FrenchOperationManualHigh PressureHoseEngine OilSpray GunMulti-Adjustable Spray WandKn
8- ENGD279183. Connect wand to gun. Tighten securely.2. Place handle assembly onto frame and connect handle to frame. NOTE:Knobs are assembled to the
9- ENGD27918c. Place grooves in accessories panel assembly onto screws and slidepanel assembly into place.d. Place screws (removed earlier) into the t
Komentarze do niniejszej Instrukcji