Delta 37-195 Instrukcja Użytkownika Strona 1

INSTRUCTION MANUAL6" Professional Jointer(Model 37-195)(Model 37-275X)PART NO. 909995 - 01-22-03Copyright © 2003 Delta MachineryTo learn more abo

10ASSEMBLING FENCECARRIAGE ASSEMBLY1. Fasten fence carriage assembly (A) Fig. 15, tocutterhead pulley guard/carriage mounting bracket (C).Align the ho

11ASSEMBLINGCUTTERHEAD GUARD1. Remove set screw (A) Fig. 20 from cutterhead guardpost (F) with the 2.5mm hex wrench. Insert post (F)through hole in th

12ASSEMBLING DUST CHUTEThe jointer stand has a built-in dust chute (A) Fig. 25. If this machine is to be used with a dust collection system, thesuppli

13LOCKING SWITCHIN THE “OFF” POSITIONIMPORTANT: When the tool is not in use, the switchshould be locked in the “OFF” position to preventunauthorized

14INFEED TABLEPOSITIVE STOPSDISCONNECT MACHINE FROMPOWER SOURCE.Positive stops are provided to limit the height and depthof the infeed table. To adjus

155. If the knife is high or low at either end, slightly turnthe four screws (D) Fig. 41, in the knife locking barclockwise to loosen using the wrench

16ADJUSTING TABLE GIBS“Gibs”’ are provided to take up all play between themating dovetail ways of the base and the infeed andoutfeed tables. The ”gib”

17ADJUSTING FENCEPOSITIVE STOPNOTE: SWITCH HAS BEEN REMOVED FOR CLARITYOF ILLUSTRATIONS ONLY.The fence on this jointer is equipped with positive stops

18REMOVING, REPLACING,AND RESETTING KNIVESIf the knives are removed from the cutterhead for re-placement or sharpening, care must be used inremoving,

13. Rotate the cutterhead by hand until the knife is at itshighest point at each end of the cutterhead. To raise theknife, use wrench (E) Fig. 58, and

2Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with

20Fig. 63Fig. 64Fig. 65SURFACINGSurfacing is identical to the jointing operation except forthe position of the workpiece. For surfacing, the major fla

21Fig. 66Fig. 67Fig. 68 Fig. 69After considerable use, the knives will become dull and it will not be possible to do accurate work. Unlessbadly damage

22PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

23Printed in U.S.A.Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machin

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

317. REDUCE THE RISK OF UNINTENTIONAL STARTING.Make sure switch is in “OFF” position before plugging inpower cord. In the event of a power failure, mo

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp tim

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug a

6JOINTER PARTSFig. 41. Jointer2. Fence Carriage Assembly3. Cutterhead Pulley Guard/Carriage MountingBracket4. Switch Mounting Bracket5. Cutterhead Gua

7Fig. 516. Stand with Pre-Wired Switch17. Dust Chute18. V-Belt19. Pulley20. M10x1.5x20mm Hex Socket Head Screw (3)21. M8x1.25x55mm Hex Socket Head Scr

8ASSEMBLINGJOINTER TO STAND1. The outfeed end (N) Fig. 9, of the jointer must bepointing toward the end of the stand with dust chuteopening (B) Fig. 7

9ASSEMBLING BELT ANDALIGNING PULLEYS1. Place belt (A) Fig. 11, in groove of cutterhead pulley(B) and motor pulley (C).2. Make certain the motor pulley