Delta 43-420 Instrukcja Obsługi Strona 1

INSTRUCTION MANUALDATED 9-17-99 PART NO. 432-02-651-0012©Delta International Machinery Corp. 1999Platinum Edition 2-SpeedHeavy-Duty Wood Shaper(Model

10Fig. 14Fig. 16Fig. 17Fig. 18ASSEMBLING FENCETO SHAPER TABLE1. The fence on this shaper can be mounted parallelto the miter gage slot using two holes

11Fig. 19Fig. 20Fig. 21Fig. 23Fig. 225. Fig. 19, illustrates fence body (C) fastened to thetable with the two fence locking handles (F).6. Loosen lock

12Fig. 24Fig. 25Fig. 26Fig. 27 Fig. 28ASSEMBLING GUARDSTO FENCE BODY1. Assemble guard bracket (A) Fig. 24, and hex rod (B)to upright hex shaft (C) as

13Fig. 29Fig. 30Fig. 316. Fig. 29, illustrates complete fence and guard assemblymounted in the alternate position, 90 degrees to mitergage slot.ASSEMB

14Fig. 34Fig. 36 Fig. 37Fig. 35ASSEMBLINGTABLE INSERTSThree table inserts are provided for various size cutters,as shown in Fig. 34. The large insert

15Fig. 38Fig. 39Fig. 40ASSEMBLING SPINDLE GUARDA 4-1/2 diameter spindle guard is supplied as standard equipment and is supplied with a 1/2 bushing whi

16CONNECTING SHAPER TO POWER SOURCEGROUNDING INSTRUCTIONSCAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATORFROM ELECTRIC SHOCK.I

17STARTING AND STOPPING THE SHAPERTo apply power to the machine, push “ON” button (A) Fig. 43. To stop the machine, push“OFF” button (B).LOCKING SWITC

18Fig. 45Fig. 46Fig. 47RAISING ANDLOWERING SPINDLEThe spindle can be raised or lowered by loosening lockknob (A) Fig. 45, and turning handwheel (B). T

19FENCE CONTROLS AND ADJUSTMENTSFig. 50 Fig. 51Fig. 491. DISCONNECT SHAPER FROM POWER SOURCE. IMPORTANT: The fence halves (A) Fig. 48, should beadjust

2TABLE OF CONTENTSSAFETY RULES ...

20Fig. 53Fig. 54Fig. 55Fig. 52GUARD CONTROLSAND ADJUSTMENTSDISCONNECT SHAPER FROM POWER SOURCE.The spring clamp (A) Fig. 52, holddown (B), and clearpl

21Fig. 564. Loosen thumb screws on guard mounting bracket (P)Fig. 56, and adjust spring clamp (N) so it will provideinward pressure on workpiece; then

22SHAPING WITH COLLARS AND STARTING PINWhen shaping with collars and starting pin, the following rules must always be followed for good workand safety

23Fig. 67 Fig. 68Fig. 69Fig. 70Fig. 71STARTING PIN1. Your machine is supplied with a tapered starting pin(A) Fig. 67, which is used as a support when

24Delta Shaper AccessoriesHigh-Speed Steel3-Lip Shaper CuttersAll have 1/2spindle hole. Involute relief designpermits honing of the face without chang

25Delta Shaper Accessories (continued)Door Edge DetailAll 215/16diameter.3/4bore, 1/2T-Bushing.Bead or Half Round ConcaveAll 215/16diameter.3/4bore,

26Delta Shaper Accessories (continued)Male and Female SashAll 215/16diameter.3/4bore with 1/2T-Bushing.Drawer JointAll 215/16diameter.3/4bore, 1/2T-

27Delta Shaper Accessories (continued)Double Sided 8-Cutter Cope and Pattern SetIncludes 1/4and 1/2wide x 5/8tongue andgroove cutters. All 215/16dia

28Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, ormachine accessory which in normal use has proven

3SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certainhazards in

4ADDITIONAL SAFETY RULES FOR WOOD SHAPERS1. WARNING: DO NOT OPERATE YOUR WOODSHAPER UNTIL IT IS COMPLETELY ASSEMBLED ANDINSTALLED ACCORDING TO THE INS

5UNPACKING AND CLEANINGCarefully unpack the shaper and fence system from the shipping containers. Clean all loose parts and removethe protective coati

64. 10 Wide Cast Iron Extension Wings5. Wrenches (2)6. 7/16-20 x 1 Hex Cap Screws (6) for mountingextension wings7. Flat Washers (6) for mounting exte

727. Fence Body28. Left and Right fence halves29. Locking Levers (2) for fence halves30. Flat Washers (2) for locking levers31. Spring clamp for fence

ASSEMBLY INSTRUCTIONSWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SHAPER TO THE POWER SOURCEUNTIL THE SHAPER IS COMPLETELY ASSEMBLED AND YOU HAVE

9Fig. 9 Fig. 10Fig. 11Fig. 13Fig. 12ASSEMBLINGSWITCH BRACKETAND ON/OFF SWITCH1. The on/off switch (A) Fig. 9, and switch mountingbracket (B) are shipp